Hey folks.
I just got some gigabit ethernet cards to replace my fddi
back-end network. The install went well (trivial) but all
release, non-5.x, DataONTAP versions have some bugs with
the gigabit ethernet.
So, I upgraded to 4.3.4D2 which supposedly has the fix.
It works well on my f540.
My f630 pukes horribly:
Probing devices
Finding image...
Loading 14 f 5 disk@0
Complete
Starting NetApp Release 4.3.4D2: Wed May 13 07:55:56 PDT 1998
Copyright (c) 1992-1998 Network Appliance, Inc.
PANIC: MM fault MMCSR=1, type=1, VA=0x79dba0, PC=0xfffffc00002a2d44
version: NetApp Release 4.3.4D2: Wed May 13 07:55:56 PDT 1998
cc flags: 1
dumping core: Error dumping core --- not dumped.
ok c
I quickly put the 4.3.3 boot floppy I had and we are back in service
and I am calming down.. :)
So, anybody able to decode this error? My filer is:
whirlpool> sysconfig -v
NetApp Release 4.3.3: Mon Mar 16 12:58:27 PST 1998
System ID: 0016786960
slot 0: System Board (NetApp System Board IV rev-b)
Firmware release: 1.8_a1
Memory Size: 512 MB
slot 2: Ethernet Controller e2 (Znyx)
MAC Address: 00:c0:95:f8:2f:6d (Twisted pair)
slot 3: FDDI Network Adapter f3 (DEC 3002)
MAC Address: 00:00:f8:bd:c6:04 (Dual Attach Fiber)
slot 8: Dual SCSI Host Adapter (NetApp SCSI Adapter I)
SCSI Host Adapter 8a (Qlogic ISP 1040B)
Firmware Version 2.26 Clock Rate 40MHz.
0: SEAGATE ST19171W 0023 Size=8.3GB (17783112 blocks)
1: SEAGATE ST19171W 0023 Size=8.3GB (17783112 blocks)
2: SEAGATE ST19171W 0023 Size=8.3GB (17783112 blocks)
3: SEAGATE ST19171W 0023 Size=8.3GB (17783112 blocks)
8: SEAGATE ST19171W 0023 Size=8.3GB (17783112 blocks)
9: SEAGATE ST19171W 0023 Size=8.3GB (17783112 blocks)
10: SEAGATE ST19171W 0023 Size=8.3GB (17783112 blocks)
11: SEAGATE ST19171W 0023 Size=8.3GB (17783112 blocks)
12: SEAGATE ST19171W 0023 Size=8.3GB (17783112 blocks)
EMU 0: P/N 500408 S/N 2550270236 Firmware Rev 1.19
0 Swap Events, 0 Enclosure Events
EMU 1: P/N 500408 S/N 2550272530 Firmware Rev 1.19
0 Swap Events, 0 Enclosure Events
SCSI Host Adapter 8b (Qlogic ISP 1040B)
Firmware Version 2.26 Clock Rate 40MHz.
0: SEAGATE ST19171W 0023 Size=8.3GB (17783112 blocks)
1: SEAGATE ST19171W 0023 Size=8.3GB (17783112 blocks)
2: SEAGATE ST19171W 0023 Size=8.3GB (17783112 blocks)
3: SEAGATE ST19171W 0023 Size=8.3GB (17783112 blocks)
9: SEAGATE ST19171W 0023 Size=8.3GB (17783112 blocks)
10: SEAGATE ST19171W 0023 Size=8.3GB (17783112 blocks)
11: SEAGATE ST19171W 0023 Size=8.3GB (17783112 blocks)
12: SEAGATE ST19171W 0023 Size=8.3GB (17783112 blocks)
EMU 2: P/N 500408 S/N 2550272276 Firmware Rev 1.19
0 Swap Events, 0 Enclosure Events
EMU 3: P/N 500408 S/N 2550272259 Firmware Rev 1.19
0 Swap Events, 0 Enclosure Events
slot 9: NVRAM (NetApp NVRAM II)
Revision: A1
Serial Number: 9744
Memory Size: 16 MB
Battery 1 Status: 100% (3.30v)
Battery 2 Status: 100% (3.29v)
slot 10: Gigabit Ethernet Controller e10
MAC Address: 00:60:cf:20:48:61 (1000fx)
whirlpool>
I need gigabit pretty badly but don't want to go to 5.x yet.
Anybody?
Thanks.
Alex
This archive was generated by hypermail 2b29 : Tue Jan 04 2000 - 10:19:43 EST